The Baudot code, invented by Émile Baudot, is a character set predating EBCDIC and ASCII. It was the predecessor to the International Telegraph Alphabet No. 2 (ITA2), the teleprinter code in use until the advent of ASCII. Each character in the alphabet is represented by a series of bits, sent over a communication channel such as a telegraph wire or a radio signal. The symbol rate measurement is known as baud, and is derived from the same name.
Baudot code 
Technically, five bit codes began in the 16th century, when Francis Bacon developed the cipher now called Bacon's cipher. However, this cipher is not a machine cipher and as such is not readily suitable for telecommunications.
Baudot invented his original code in 1870 and patented it in 1874. It was a 5-bit code, with equal on and off intervals, which allowed telegraph transmission of the Roman alphabet and punctuation and control signals. It was based on an earlier code developed by Carl Friedrich Gauss and Wilhelm Weber in 1834.
Baudot's original code was adapted to be sent from a manual keyboard, and no teleprinter equipment was ever constructed that used it in its original form. The code was entered on a keyboard which had just five piano type keys, operated with two fingers of the left hand and three fingers of the right hand. Once the keys had been pressed they were locked down until mechanical contacts in a distributor unit passed over the sector connected to that particular keyboard, when the keyboard was unlocked ready for the next character to be entered, with an audible click (known as the "cadence signal") to warn the operator. Operators had to maintain a steady rhythm, and the usual speed of operation was 30 words per minute.
The table above "shows the allocation of the Baudot code which was employed in the British Post Office for continental and inland services. It will be observed that a number of characters in the continental code are replaced by fractionals in the inland code. Code elements 1, 2 and 3 are transmitted by keys 1, 2 and 3, and these are operated by the first three fingers of the right hand. Code elements 4 and 5 are transmitted by keys 4 and 5, and these are operated by the first two fingers of the left hand."   
Baudot's code became known as International Telegraph Alphabet No. 1, and is no longer used.
Murray code 
In 1901 Baudot's code was modified by Donald Murray (1865–1945), prompted by his development of a typewriter-like keyboard. The Murray system employed an intermediate step, a keyboard perforator, which allowed an operator to punch a paper tape, and a tape transmitter for sending the message from the punched tape. At the receiving end of the line, a printing mechanism would print on a paper tape, and/or a reperforator could be used to make a perforated copy of the message. As there was no longer a direct correlation between the operator's hand movement and the bits transmitted, there was no concern about arranging the code to minimize operator fatigue, and instead Murray designed the code to minimize wear on the machinery, assigning the code combinations with the fewest punched holes to the most frequently used characters.
The Murray code also introduced what became known as "format effectors" or "control characters" – the CR (Carriage Return) and LF (Line Feed) codes. A few of Baudot's codes moved to the positions where they have stayed ever since: the NULL or BLANK and the DEL code. NULL/BLANK was used as an idle code for when no messages were being sent.
Early British Creed machines used the Murray system.
Western Union 
Murray's code was adopted by Western Union which used it until the 1950s, with a few changes that consisted of omitting some characters and adding more control codes. An explicit SPC (space) character was introduced, in place of the BLANK/NULL, and a new BEL code rang a bell or otherwise produced an audible signal at the receiver. Additionally, the WRU or "Who aRe yoU?" code was introduced, which caused a receiving machine to send an identification stream back to the sender.
Around 1930, the CCITT introduced the International Telegraph Alphabet No. 2 (ITA2) code as an international standard, which was based on the Western Union code with some minor changes. The US standardized on a version of ITA2 called the American Teletypewriter code (USTTY) which was the basis for 5-bit teletypewriter codes until the debut of 7-bit ASCII in 1963.
|Pattern of impulses
|Letter shift||Figure shift|
|msb on left||msb on right|
|01000||00010||Carriage return||Carriage return|
|00010||01000||Line feed||Line feed|
|11011||11011||Shift to figures|
|11111||11111||Shift to letters|
ITA2 is still used in TDDs, telex, and some amateur radio applications, such as radioteletype ("RTTY"). ITA2 is also used in Enhanced Broadcast Solution (a recent financial protocol specified by Deutsche Börse) to reduce the character encoding footprint
Nearly all 20th-century teleprinter equipment used Western Union's code, ITA2, or variants thereof. Radio amateurs casually call ITA2 and variants "Baudot" incorrectly, and even the American Radio Relay League's Amateur Radio Handbook does so, though in more recent editions the tables of codes correctly identifies it as ITA2.
NOTE: This table presumes the space called "1" by Baudot and Murray is rightmost, and least significant. The way the transmitted bits were packed into larger codes varied by manufacturer; the most common solution allocates the bits from the least significant bit towards the most significant bit (leaving the three most significant bits of a byte unused).
In ITA2, characters are expressed using five bits. ITA2 uses two code sub-sets, the "letter shift" (LTRS), and the "figure shift" (FIGS). The FIGS character (11011) signals that the following characters are to be interpreted as being in the FIGS set, until this is reset by the LTRS (11111) character. In use, the LTRS or FIGS shift key is pressed and released, transmitting the corresponding shift character to the other machine. The desired letters or figures characters are then typed. Unlike a typewriter or modern computer keyboard the shift key isn't kept depressed whilst the corresponding characters are typed. "ENQuiry" will trigger the other machine's answerback. It means "Who are you?"
CR is carriage return, LF is line feed, BEL is the bell character which rang a small bell (often used to alert operators to an incoming message), SP is space, and NUL is the null character (blank tape).
Note: the binary conversions of the codepoints are often shown in reverse order, depending on (presumably) from which side one views the paper tape. Note further that the "control" characters were chosen so that they were either symmetric or in useful pairs so that inserting a tape "upside down" did not result in problems for the equipment and the resulting printout could be deciphered. Thus FIGS (11011), LTRS (11111) and space (00100) are invariant, while CR (00010) and LF (01000), generally used as a pair, result in the same output when the tape is reversed. LTRS could also be used to overpunch characters to be deleted on a paper tape (much like DEL in 7-bit ASCII).
The sequence RYRYRY... is often used in test messages, and at the start of every transmission. Since R is 01010 and Y is 10101, the sequence exercises much of a teleprinter's mechanical components at maximum stress. Also, at one time, fine-tuning of the receiver was done using two coloured lights (one for each tone). 'RYRYRY...' produced 0101010101..., which made the lights glow with equal brightness when the tuning was correct. This tuning sequence is only useful when ITA2 is used with two-tone FSK modulation, such as is commonly seen in Radioteletype (RTTY) usage.
US implementations of Baudot code may differ in the addition of a few characters, such as #, & on the FIGS layer. The above table represents the US TTY code.
The Russian version of Baudot code (MTK-2) used three shift modes; the Cyrillic letter mode was activated by the character (00000). Because of the larger number of characters in the Cyrillic alphabet, the characters !, &, £, and BEL were omitted and replaced by Cyrillics.
See also 
- Ralston, Anthony; Reilly, Edwin D., eds. (1993), "Baudot Code", Encyclopedia of Computer Science (Third ed.), New York: IEEE Press/Van Nostrand Reinhold, ISBN 0-442-27679-6
- Bacon’s Bilateral Cipher, retrieved 15 April 2012
- H. A. Emmons (1 May 1916). "Printer Systems". Wire & Radio Communications 34: 209.
- William V. Vansize (25 Jan 1901). "A New Page-Printing Telegraph". Transactions (American Institute of Electrical Engineers) 18: 22.
- "Gauss-Weber-Telegraph". Metrology Mile (in German). Measurement Valley. Retrieved 2009-05-03.
- Jennings 2004
- Beauchamp, K.G. (2001). History of Telegraphy: Its Technology and Application. IET. pp. 394–395. ISBN 0-85296-792-6.
- Alan G. Hobbs, 5 Unit Codes, section Baudot Multiplex System
- Gleick, James (2011). The Information: A History, a Theory, a Flood. London: Fourth Estate. p. 203. ISBN 978-0-00-742311-8.
- Foster, Maximilian (August 1901). "A Successful Printing Telegraph". The World's Work: A History of Our Time II: 1195–1199. Retrieved 2009-07-09.
- Copeland 2006, p. 38
- Smith, Gil (2001). "Teletype Communication Codes". Baudot.net. Archived from the original on 20 August 2008. Retrieved 2008-07-11.
- dataIP Limited. "The "Baudot" Code". Archived from the original on 26 August 2010. Retrieved 9 October 2010
- "Enhanced Broadcast Solution – Interface Specification Final Version". Deutsche Börse. 17 May 2010. Retrieved 10 August 2011.
- Gillam, Richard (2002). Unicode Demystified:. Addison-Wesley. p. 30. ISBN 0-201-70052-2. Enhanced Broadcast Solution – Interface Specification Final Version
- Copeland, B. Jack, ed. (2006), Colossus: The Secrets of Bletchley Park's Codebreaking Computers, Oxford: Oxford University Press, ISBN 978-0-19-284055-4
- Hobbs, Alan G, NADCOMM Papers and Writings: Five-unit codes, retrieved 15 April 2012
- Jennings, Tom (2004), An annotated history of some character codes: Baudot's code, retrieved 17 April 2012
- MTK-2 code table
- Baudot, Murray, ITA2, ITA5, etc.
- Jean-Maurice-Émile Baudot; (includes photos of 1870s–1880s gear, tech details & references)
- Online Text-ITA2-Converter